Overview:
AP6113 is a circuit specially designed for high-precision linear lithium battery chargers, which is very suitable for low-cost, portable chargers
use. It integrates high-precision pre-charging, constant current charging, constant voltage charging, battery status detection, low leakage at the end of charging, and charging status indication
Equal performance in one, can be widely used in EPC, mobile multimedia, handheld devices and other fields.
AP6113 determines its state of charge by detecting the battery voltage: pre-charge, constant-current charging, and constant-voltage charging. When the battery voltage is less than the threshold voltage
When V MIN (generally 9V), it is in the pre-charged state, and the battery is charged with a small current. The pre-charged current can be passed through the external power supply.
Resistance to make adjustments. After pre-charging makes the battery voltage reach V MIN, it enters the fast charging state of constant current charging, and the charging current I REG can be
Adjusted by the peripheral resistor R1, the constant current charging makes the battery voltage rise to the constant voltage charging voltage V REG (typically 12.6V). Then
In the constant voltage charging state, the accuracy of the charging voltage is better than ±1%. In this state, the charging current will gradually decrease. When the charging current is less than the threshold
Value I TERM, charging is over. After charging, the battery voltage will always be monitored. When the battery voltage is less than the threshold V RECHG
(Generally V REG －200mV), recharge the battery and enter the next charging cycle.
AP6113 can also increase the end-of-saturation voltage of the battery by adjusting the peripheral resistance, which can be set to the required voltage point.
Features:
1: Ideal control circuit for 12.6V three-cell lithium-ion or lithium polymer battery charger;
2: Voltage accuracy higher than 1%;
3: Constant current charging, adjustable charging current
4: Constant voltage charging process
5: Automatic recharging process
6: Adjustable battery saturation end voltage
7: Dual LED charging status indication
8: Detection of abnormal battery status
9: When the power supply voltage is low, in Sleep mode with low power consumption, the battery leakage current is very small
10: Very few peripheral components
11: Miniaturized SOP8 package
AP6154 linear lithium battery charging IC + anti-reverse connection + overvoltage protection + short circuit protection
describe:
AP6154 is a complete single-cell lithium-ion battery with constant current/constant voltage linear charger. Its SOT package and fewer external components
The purpose makes the AP6154 an ideal choice for portable applications. AP6154 can work with USB power supply and adapter power supply.
Because AP6154 adopts internal structure and anti-reverse charging circuit, it does not need external detection resistor and isolation diode. Thermal feedback can
The charging current is adjusted to limit the chip temperature under high-power operation or high ambient temperature conditions. The charging voltage is fixed at, and
The charging current can be set externally through a resistor. When the charging current drops to the set value after reaching the final float voltage, AP6154
The charging cycle will be automatically terminated.
When the input voltage (AC adapter or power supply) is removed, AP6154 automatically enters a low current state, reducing the battery leakage current to
Below 1UA. AP6154 can also be put into shutdown mode to reduce the supply current to 25UA. Other features of AP6154 include charging current monitoring
Controller, under-voltage lockout, automatic recharge, and a status pin for indicating the end of charging and input voltage access.
Features:
1: Lithium battery positive and negative polarity reverse connection protection function
2: Short-circuit protection at the output terminal, reducing the supply current to 0
3: Input power supply voltage overvoltage chip shutdown protection
4: Programmable charging current up to 700mA
5: No need for MOSFET, sense resistor or isolation diode
6: For single-cell lithium-ion batteries, a complete linear charger in a package
7: Constant current/constant voltage operation, and has a thermal regulation function that can maximize the charging rate without the risk of overheating
8: 4.2V preset charging voltage with an accuracy of ±1%
9: Automatic recharging
10: Charge status output pin
11: C/10 charge termination
12: The power supply current in standby mode is 25uA
13: 2.9V trickle charge device version
14: Available in 5-pin SOT-23 package
AP6155 linear lithium battery charging IC + anti-reverse connection + overvoltage protection + short circuit protection
describe:
AP6155 is a complete single-cell lithium-ion battery with constant current/constant voltage linear charger. Its SOT package and fewer external components
The number of pieces makes AP6155 an ideal choice for portable applications. AP6155 can work with USB power supply and adapter power supply
Due to the internal PMOSFET architecture and the anti-reverse charging circuit, there is no need for external detection resistors and isolation diodes. Thermal feedback can
The charging current is adjusted to limit the chip temperature under high-power operation or high ambient temperature conditions. The charging voltage is fixed at, and
The charging current can be set externally through a resistor. When the charging current drops to the set value after reaching the final float voltage, AP6155
The charging cycle will be automatically terminated.
When the input voltage (AC adapter or USB power supply) is removed, AP6155 automatically enters a low current state to reduce battery leakage current.
To below 1UA. AP6155 can also be put into shutdown mode to reduce the supply current to 25UA. Other features of AP6155 include charging current
Monitor, under-voltage lockout, automatic recharge, and a status pin for indicating the end of charging and input voltage access.
关注微信公众号
